Industrijski router RUT956, Teltonika

MOBILE

Mobile module – 4G (LTE) – Cat 4 up to 150 Mbps, 3G – Up to 42 Mbps, 2G – Up to 236.8 kbps

SIM switch – 2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protection

Status – Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, Bytes sent/received, connected band, IMSI, ICCID

SMS – SMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP

USSD – Supports sending and reading Unstructured Supplementary Service Data messages

Black/White list – Operator black/white list

Multiple PDN – Possibility to use different PDNs for multiple network access and services

Band management – Band lock, Used band status display

APN – Auto APN

Bridge – Direct connection (bridge) between mobile ISP and device on LAN

Passthrough – Router assigns its mobile WAN IP address to another device on LAN

WIRELESS

Wireless mode – IEEE 802.11b/g/n, Access Point (AP), Station (STA)

WiFi security – WPA2-Enterprise – PEAP, WPA2-PSK, WEP, WPA-EAP, WPA-PSK; AES-CCMP, TKIP, Auto Cipher modes, client separation

SSID/ESSID – SSID stealth mode and access control based on MAC address

WiFi users – Up to 100 simultaneous connections

Wireless Hotspot – Captive portal (Hotspot), internal/external Radius server, built in customizable landing page

ETHERNET

WAN – 1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX

LAN – 3 x LAN ports, 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX

NETWORK

Routing – Static routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, NHRP)

Network protocols – TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SMNP, MQTT, Wake On Lan (WOL)

VoIP passthrough support – H.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packets

Connection monitoring – Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection

Firewall – Port forward, traffic rules, custom rules

DHCP – Static and dynamic IP allocation, DHCP Relay, Relayd

QoS / Smart Queue Management (SQM) – Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e

DDNS – Supported >25 service providers, others can be configured manually

Network backup – WiFi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic Failover

Load balancing – Balance Internet traffic over multiple WAN connections

Hotspot – Internal/external Radius server, captive portal, built in customizable landing page

SSHFS – Possibility to mount remote file system via SSH protocol

SECURITY

Authentication – Pre-shared key, digital certificates, X.509 certificates

Firewall – Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T

Attack prevention – DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)

VLAN – Port and tag based VLAN separation

Mobile quota control – Custom data limits for both SIM cards

WEB filter – Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only

Access control – Flexible access control of TCP, UDP, ICMP packets, MAC address filter

VPN

OpenVPN – Multiple clients and a server can run simultaneously, 12 encryption methods

OpenVPN Encryption – DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC

IPsec – IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)

GRE – GRE tunnel

PPTP, L2TP – Client/Server instances can run simultaneously, L2TPv3 support

Stunnel – Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code

DMVPN – Method of building scalable IPsec VPNs

SSTP – SSTP client instance support

ZeroTier – ZeroTier VPN client support

WireGuard – WireGuard VPN client and server support

MODBUS TCP SLAVE

ID range – Respond to one ID in range [1;255] or any

Allow Remote Access – Allow access through WAN

Custom registers – MODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Slave functionality

MODBUS TCP MASTER

Supported functions – 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats – 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC)

MODBUS RTU MASTER (RS232)

Supported baud rates – From 300 to 115200

Supported functions – 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats – 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

Number of data bits – From 5 to 8

Number of stop bits – 1 or 2

Parity – None, Even, Odd

Flow – None, RTS/CTS, Xon/Xoff

Duplex – Full duplex

MODBUS RTU MASTER (RS485)

Supported baud rates – From 300 to 300000

Supported functions – 01, 02, 03, 04, 05, 06, 15, 16

Supported data formats – 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

Number of data bits – 8

Number of stop bits – 1

Parity – None, Even, Odd

Flow – None, Xon/Xoff

Duplex – Half duplex

MODBUS DATA TO SERVER

Protocol – HTTP(S), MQTT, Azure MQTT

MQTT GATEWAY

MQTT Gateway – Allows sending commands and receiving data from MODBUS Master through MQTT broker

DNP3

Supported modes – TCP Master, DNP3 Outstation, RTU Master

MONITORING & MANAGEMENT

WEB UI – HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log

FOTA – Firmware update from server, automatic notification

SSH – SSH (v1, v2)

SMS – SMS status, SMS configuration, send/read SMS via HTTP POST/GET

Call – Reboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer, WiFi on/off

TR-069 – OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem

MQTT – MQTT Broker, MQTT publisher

SNMP – SNMP (v1, v2, v3), SNMP Trap

JSON-RPC – Management API over HTTP/HTTPS

MODBUS – MODBUS TCP status/control

RMS – Teltonika Remote Management System (RMS)

IOT PLATFORMS

Cloud of Things – Allows monitoring of: Device data, Mobile data, Network info, Availability

ThingWorx – Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type

Cumulocity – Allows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength

Azure IoT Hub – Can send device IP, Number of bytes send/received, Temperature, PIN count to Azure IoT Hub server, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type

SYSTEM CHARACTERISTICS

CPU – Mediatek MIPS 24Kc 580 MHz

RAM – 128 MB, DDR2

FLASH storage – 16 MB, SPI Flash

FIRMWARE / CONFIGURATION

WEB UI – Update FW from file, check FW on server, configuration profiles, configuration backup

FOTA – Update FW

RMS – Update FW/configuration for multiple devices at once

Keep settings – Update FW without losing current configuration

FIRMWARE CUSTOMIZATION

Operating system – RutOS (OpenWrt based Linux OS)

Supported languages – Busybox shell, Lua, C, C++

Development tools – SDK package with build environment provided

LOCATION TRACKING

GNSS – GPS, GLONASS, BeiDou, Galileo and QZSS

Coordinates – GNSS coordinates via WebUI, SMS, TAVL, RMS

NMEA – NMEA 0183

NTRIP – NTRIP protocol (Networked Transport of RTCM via Internet Protocol)

Server software – Supported server software TAVL, RMS

Geofencing – Configurable multiple geofence zones

SERIAL

RS232 – DB9 connector, full RS232 (with RTS, CTS)

RS485 – RS485 Full Duplex (4 wires) and Half Duplex (2 wires). 300-115200 baud rate

Serial functions – Console, Serial over IP, Modem, MODBUS gateway, NTRIP Client

USB

Data rate – USB 2.0

Applications – Samba share, USB-to-serial

External devices – Possibility to connect external HDD, flash drive, additional modem, printer

Storage formats – FAT, FAT32, NTFS

INPUT / OUTPUT

Input – 1 x digital dry input (0 – 3 V), 1 x digital galvanically isolated input (0 – 30 V), 1 x analog input (0 – 24 V), 1 x Digital non-isolated input (on 4-pin power connector, 0 – 5 V detected as logic low, 8 – 30 V detected as logic high)

Output – 1 x digital open collector output (30 V, 250 mA), 1 x SPST relay output (40 V, 4 A), 1 x Digital open collector output (30 V, 300 mA, on 4-pin power connector)

Events – Email, RMS, SMS

I/O juggler – Allows to set certain I/O conditions to initiate event

POWER

Connector – 4-pin industrial DC power socket

Input voltage range – 9 – 30 VDC, reverse polarity protection; surge protection >31 VDC 10us max

PoE (passive) – Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, LAN1 Port, 9 – 50 VDC

Power consumption – < 2 W idle, < 7 W Max

PHYSICAL INTERFACES

Ethernet – 4 x RJ45 ports, 10/100 Mbps

I/O’s – 2 x Inputs and 2 x Outputs on 10-pin industrial socket, 1 x Digital input and 1 x Digital output on 4-pin power connector (available from HW revision 1600)

Status LEDs – 1 x bi-color connection status LED, 5 x connection strength LEDs, 4 x LAN status LEDs, 1 x Power LED

SIM – 2 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V, external SIM holders, eSIM (Optional)

Power – 1 x 4-pin power connector

Input/output – 1x 10 pin industrial socket for inputs/outputs

Antennas – 2 x SMA for LTE, 2 x RP-SMA for WiFi, 1 x SMA for GNSS

USB – 1 x USB A port for external devices

RS232 – 1 x DB9 socket

RS485 – 1 x 6-pin industrial socket

Reset – Reboot/User default reset/Factory reset button

PHYSICAL SPECIFICATION

Casing material – Aluminium housing, plastic panels

Dimensions (W x H x D) – 110 x 50 x 100 mm

Weight – 287 g

Mounting options – DIN rail (can be mounted on two sides), flat surface placement

OPERATING ENVIRONMENT

Operating temperature – -40 °C to 75 °C

Operating humidity – 10% to 90% non-condensing

Ingress Protection Rating – IP30

REGULATORY & TYPE APPROVALS

Regulatory – CE/RED, UKCA, CB

EMI IMMUNITY

Standards – EN 301 489-1 V2.2.3, EN 301 489-17 V3.2.4, Draft EN 301 489-19 V2.2.0, Final draft EN 301 489-52 V1.2.0, EN 55032:2015+A1:2020, EN 55035:2017+A11:2020, EN 61000-3-3:2013+A1:2019, EN IEC 61000-3-2:2019

ESD – EN 61000-4-2:2009

RS – EN 61000-4-3:2020

EFT – EN 61000-4-4:2012

Surge immunity (AC Power Line) – EN 61000-4-5:2014+A1:2017

CS – EN 61000-4-6:2009

DIP – EN IEC 61000-4-11:2020

PERFORMANCE SPECIFICATIONS

Standard – EN 300 328 V2.2.2, EN 301 908-1 V13.1.1, EN 301 908-2 V13.1.1, EN 301 908-13 V13.1.1, EN 303 413 V1.1.1

SAFETY

Standards – EN IEC 62311:2020
AS/NZS 60950.1:2015
IEC 62368-1:2018,
EN IEC 62368-1:2020+A11:2020